List of Issues

Chinese Journal of Chromatography
2024, Vol. 42, No. 8
Online: 08 August 2024

Previous Issue    Next Issue



For Selected:

Download Citations EndNote Ris BibTeX

Toggle Thumbnails

Select

CONTENTS 2024, 42 (8):  0-0.  Abstract ( 38 )   PDF (2817KB) ( 38 )

Articles

Select

Simultaneous determination of 21 perfluorinated and polyfluoroalkyl substances in plant oils by ultra-high performance liquid chromatography-triple quadrupole mass spectrometry FENG Hao, ZHANG Wei, HE Baoshan, LI Panpan, GAO Shuqing, GUO Baoyuan, YANG Yongtan 2024, 42 (8):  731-739.  DOI: 10.3724/SP.J.1123.2024.01014 Abstract ( 153 )   HTML ( 42 )   PDF (2178KB) ( 128 )   Edible plant oils are a key component of the daily human diet, and the quality and safety of plant oils are related to human health. Perfluorinated and polyfluoroalkyl substances (PFASs) are pollutants that can contaminate plant oil through the processing of raw materials or exposure to materials containing these substances. Thus, establishing a sensitive and accurate analytical method for the determination of PFASs is critical for ensuring the safety of plant oils. In this study, a method based on acetonitrile extraction and solid phase extraction purification combined with ultra-high performance liquid chromatography-triple quadrupole mass spectrometry (UHPLC-MS/MS) was developed for the simultaneous determination of 21 PFASs, including perfluorocarboxylic acids, perfluoroalkyl sulfonic acids, and fluorotelomer sulfonic acids, in edible plant oils. The chromatographic conditions and MS parameters were optimized, and the influences of the extraction solvents and purification method were systematically studied. Plant oil samples were directly extracted with acetonitrile and purified using a weak anion-exchange (WAX) column. The 21 target PFASs were separated on a reversed-phase C18 chromatographic column and detected using a triple quadrupole mass spectrometer with an electrospray ionization source. The mass spectrometer was operated in negative-ion mode. The target compounds were analyzed in multiple reaction monitoring (MRM) mode and quantified using an internal standard method. The results demonstrated that the severe interference observed during the detection of PFASs in the co-extracted substances was completely eliminated after the extraction mixture was purified using a WAX column. The 21 target PFASs showed good linearity in their corresponding ranges, with correlation coefficients greater than 0.995. The limits of detection (LODs) and limits of quantification (LOQs) of the method were in the range of 0.004-0.015 and 0.015-0.050 μg/kg, respectively. The recoveries ranged from 95.6% to 115.8%, with relative standard deviations (RSDs) in the range of 0.3%-10.9% (n=9). The established method is characterized by simple sample pretreatment, good sensitivity, high immunity to interferences, and good stability, rendering it suitable for the rapid analysis and accurate determination of typical PFASs in edible plant oils.

Select

Determination of 13 perfluorinated and polyfluoroalkyl substances in fishes by QuEChERS-ultra-high performance liquid chromatography-tandem mass spectrometry LIU Xiaoqi, LIU Zhenzhen, WANG Meiyu, GU Chenshu, WANG Xinquan, LIU Lianliang, QI Peipei 2024, 42 (8):  740-748.  DOI: 10.3724/SP.J.1123.2023.08002 Abstract ( 109 )   HTML ( 24 )   PDF (1465KB) ( 80 )   Perfluorinated and polyfluoroalkyl substances (PFASs) are compounds characterized by at least one perfluorinated carbon atom in an alkyl chain linked to side-chain groups. Owing to their unique chemical properties, these compounds are widely used in industrial production and daily life. However, owing to anthropogenic activities, sewage discharge, surface runoff, and atmospheric deposition, PFASs have gradually infiltrated the environment and aquatic resources. With their gradual accumulation in environmental waters, PFASs have been detected in fishes and several fish-feeding species, suggesting that they are bioconcentrated and even amplified in aquatic organisms. PFASs exhibit high intestinal absorption efficiencies, and they bioaccumulate at higher trophic levels in the food chain. They can be bioconcentrated in the human body via food (e. g., fish) and thus threaten human health. Therefore, establishing an efficient analytical technique for use in analyzing PFASs in typical fish samples and providing technical support for the safety regulation and risk assessment of fish products is necessary. In this study, by combining solvent extraction and magnetic dispersion-solid phase extraction (d-SPE), an improved QuEChERS method with ultra-high performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS) was developed for the determination of 13 PFASs in fish samples. Fe3O4-TiO2 can be used as an ideal adsorbent in the removal of sample matrix interference and a separation medium for the rapid encapsulation of other solids to be isolated from the solution. Based on the matrix characteristics of the fish products and structural properties of the target PFASs, Fe3O4-TiO2 and N-propyl ethylenediamine (PSA) were employed as adsorbents in dispersive purification. The internal standard method was used in the quantitative analyses of the PFASs. To optimize the sample pretreatment conditions of analyzing PFASs, the selection of the extraction solvent and amounts of Fe3O4-TiO2 and PSA were optimized. Several PFASs contain acidic groups that are non-dissociated in acidic environments, thus favoring their entry into the organic phase. In addition, acidified acetonitrile can denature and precipitate the proteins within the sample matrix, facilitating their removal. Finally, 2% formic acid acetonitrile was used as the extraction solvent, and 20 mg Fe3O4-TiO2, 20 mg PSA and 120 mg anhydrous MgSO4 were used as purification adsorbents. Under the optimized conditions, the developed method exhibited an excellent linearity (R≥0.9973) in the range of 0.01-50 μg/L, and the limits of detection (LODs) and quantification (LOQs) ranged from 0.001-0.023 and 0.003-0.078 μg/L, respectively. The recoveries of the 13 PFASs at low, medium, and high spiked levels (0.5, 10, and 100 μg/kg) were 78.1%-118%, with the intra- and inter-day precisions of 0.2%-11.1% and 0.8%-8.7%, respectively. This method was applied in analyzing real samples, and PFASs including perfluorooctanesulfonic acid, perfluorooctanoic acid, perfluoroundecanoic acid, perfluorododecanoic acid, and perfluorotridecanoic acid, were detected in all 11 samples evaluated. This method is simple, sensitive, and suitable for use in analyzing PFASs in fish samples.

Select

Rapid determination of nine preservatives in tobacco flavor by three phase-hollow fiber-liquid phase microextraction-high performance liquid chromatography WANG Ye, XIE Jianchen, HUANG Lingjie, XIA Zhicheng 2024, 42 (8):  749-757.  DOI: 10.3724/SP.J.1123.2023.08012 Abstract ( 63 )   HTML ( 18 )   PDF (1418KB) ( 56 )   Tobacco flavors are extensively utilized in traditional tobacco products, electronic nicotine, heated tobacco products, and snuff. To inhibit fungal growth arising from high moisture content, preservatives such as benzoic acid (BA), sorbic acid (SA), and parabens are often incorporated into tobacco flavors. Nonetheless, consuming preservatives beyond safety thresholds may pose health risks. Therefore, analytical determination of these preservatives is crucial for both quality assurance and consumer protection. For example, BA and SA can induce adverse reactions in susceptible individuals, including asthma, urticaria, metabolic acidosis, and convulsions. Parabens, because of their endocrine activity, are classified as endocrine-disrupting chemicals. Despite extensive research, the concurrent quantification of trace-level hydrophilic (BA and SA) and hydrophobic (methylparaben, ethylparaben, isopropylparaben, propylparaben, butylparaben, isobutylparaben, and benzylparaben) preservatives in tobacco flavors remains challenging. Traditional liquid phase extraction coupled with high performance liquid chromatography (HPLC) often results in high false positive rates and inadequate sensitivity. In contrast, tandem mass spectrometry offers high sensitivity and specificity; however, its widespread application is limited by laborious sample preparation and significant operational costs. Therefore, it is crucial to establish a fast and sensitive sample pretreatment and analysis method for the nine preservatives in tobacco flavors. In this study, a method for the simultaneous determination of the nine preservatives (SA, BA and seven parabens) in tobacco flavor was established based on three phase-hollow fiber-liquid phase microextraction (3P-HF-LPME) technology combined with HPLC. To obtain the optimal pretreatment conditions, extraction solvent type, sample phase pH, acceptor phase pH, sample phase volume, extraction time, and mass fraction of sodium chloride, were examined. Additionally, the HPLC parameters, including UV detection wavelength and mobile phase composition, were refined. The optimal extraction conditions were as follows: dihexyl ether was used as extraction solvent, 15 mL sample solution (pH 4) was used as sample phase, sodium hydroxide aqueous solution (pH 12) was used as acceptor phase, and the extraction was carried out at 800 r/min for 30 min. Chromatographic separation was accomplished using an Agilent Poroshell 120 EC-C18 column (100 mm×3 mm, 2.7 μm) and a mobile phase comprising methanol, 0.02 mol/L ammonium acetate aqueous solution (containing 0.5% acetic acid), and acetonitrile for gradient elution. Under the optimized conditions, the nine target analytes showed good linear relationships in their respective linear ranges, the correlation coefficients (r) were ≥0.9967, limits of detection (LODs) and quantification (LOQs) were 0.02-0.07 mg/kg and 0.08-0.24 mg/kg, respectively. Under two spiked levels, the enrichment factors (EFs) and extraction recoveries (ERs) of the nine target analytes were 30.6-91.1 and 6.1%-18.2%, respectively. The recoveries of the nine target analytes ranged from 82.2% to 115.7% and the relative standard deviations (RSDs) (n=5) were less than 14.5% at low, medium and high levels. The developed method is straightforward, precise, sensitive, and well-suited for the rapid screening of preservatives in tobacco flavor samples.

Select

Determination of five veterinary drug residues in milk by ultra-high performance liquid chromatography-quadrupole/electrostatic field orbitrap mass spectrometry based on modified chitosan membrane purification PAN Wang, ZHANG Shenping, WANG Anqi, HU Jun, ZHOU Lihui 2024, 42 (8):  758-765.  DOI: 10.3724/SP.J.1123.2023.08001 Abstract ( 62 )   HTML ( 17 )   PDF (5113KB) ( 26 )   Milk is an important consumer product with high nutritional value. The presence of veterinary drug residues in milk owing to the indiscriminate use of veterinary drugs may affect consumer health. In the mass spectrometric analysis of trace compounds, chromatographic co-eluting components easily interfere with the mass spectral signals obtained, affecting the accuracy of qualitative and quantitative analyses. Matrix purification is a promising method to reduce the matrix effect. Chitosan is a natural biopolymer with numerous active functional groups such as amino, acetyl, and hydroxyl groups; these groups can adsorb lipids through hydrophobic and electrostatic interactions. Chitosan also has the advantages of low production cost, stable chemical properties, and convenient modification. Novel chitosan-based materials are promising candidates for lipid purification. In this study, a chitosan membrane was modified with trimethoxyoctadecylsilane (C18-CSM). C18-CSM was prepared through one-step hydrolysis and used as a dispersive solid phase extraction (DSPE) adsorbent to purify the matrix during milk pretreatment. We combined C18-CSM with ultra-high performance liquid chromatography-quadrupole/electrostatic field orbitrap mass spectrometry (UHPLC-Q/Exactive Orbitrap MS) to develop an effective method for the extraction and determination of ofloxacin, enrofloxacin, ciprofloxacin, diazepam, and metronidazole in milk. C18-CSM was characterized using scanning electron microscopy, Fourier transform infrared spectroscopy, and water contact angle testing. The results indicated that the material has a rough surface and uniformly dense cross-section. The water contact angle of C18-CSM was 104°, indicating its good hydrophobicity. The pretreatment conditions (extraction solvent, dosage of NaCl, extraction frequency, and dosage of C18-CSM) that influenced the recoveries of the five veterinary drugs were investigated in detail. The optimal conditions were established as follows: 5% formic acid in acetonitrile, 1 g NaCl, extraction 1 time, 20 mg C18-CSM. Separation was performed on a Hypersil GOLD VANQUISH column (100 mm×2.1 mm, 1.9 μm). The mobile phase consisted of 0.1% formic acid aqueous solution and 0.1% formic acid in acetonitrile, and was flowed at a rate of 0.3 mL/min. The sample injection volume was 1 μL, and the column temperature was maintained at 25 ℃. Mass spectrometric analysis was performed in positive electrospray ionization mode. To verify the necessity of the purification material, the matrix effect was investigated using the matrix-matched standard curve method. The use of C18-CSM reduced the matrix effects of the five necessity drugs from the range of -22%-8.8% to the range of -13%-3.6%, indicating that C18-CSM is a highly efficient DSPE material. Under optimal conditions, the developed method showed good linearities within the range of 0.5-100 μg/L, with correlation coefficients (r2)≥0.9970. The limits of detection(LODs) and quantification (LOQs) were 0.2 μg/L and 0.5 μg/L, respectively. To assess the accuracy and precision of the method, we prepared milk samples with three spiked levels (low, medium, and high). The recoveries of the five veterinary drugs were ranged from 79.5% to 115%, and the intra-day and inter-day relative standard deviations were 7.0%-13% (n=6) and 1.3%-11% (n=3), respectively. This study provides a simple, accurate, and reliable method for the rapid and simultaneous determination of the five veterinary drug residues in milk.

Select

Ion chromatography-pulsed amperometry method for determination of trace hydrogen sulfide in air GAO Xiaojing, NI Tong, SHEN Rui, SHI Chaoou 2024, 42 (8):  766-772.  DOI: 10.3724/SP.J.1123.2023.10028 Abstract ( 53 )   HTML ( 11 )   PDF (787KB) ( 25 )   Hydrogen sulfide (H2S) is a pervasive gaseous pollutant that emits the characteristic odor of rotten gas, even at low concentrations. It is generated during various industrial processes, including petroleum and natural gas refining, mining operations, wastewater treatment activities, and refuse disposal practices. According to statistics from the World Health Organization (WHO), over 70 occupations are exposed to H2S, rendering it a key monitoring factor in occupational disease detection. Although H2S has legitimate uses in the chemical, medical, and other fields, prolonged exposure to this gas can cause severe damage to the respiratory and central nervous systems, as well as other organs in the human body. Moreover, the substantial release of H2S into the environment can lead to significant pollution. This noxious substance has the potential to impair soil, water, and air quality, while disrupting the equilibrium of the surrounding ecosystems. Therefore, sulfide has become one of the most commonly measured substances for environmental monitoring worldwide. Achieving the stable enrichment and accurate detection of low-level H2S is of great significance. Common methods for detecting this gas include spectrophotometry, chemical analysis, gas chromatography, rapid field detection, and ion chromatography. Although these methods provide relatively reliable results, they suffer from limitations such as high detection cost, low recovery, lack of environmental friendliness, and imprecise quantification of low-concentration H2S. Furthermore, the sampling processes involved in these methods are complex and require specialized equipment and electrical devices. Additionally, approximately 20% of the sulfides in a sample are lost after 2 h in a conventional alkaline sodium hydroxide solution, causing difficulties in preservation and detection. In this study, an accurate, efficient, and cost-saving method based on ion chromatography-pulse amperometry was developed for H2S determination. A conventional IonPac AS7 (250 mm×4 mm) anion-exchange column was employed, and a new eluent based on sodium hydroxide and sodium oxalate was used to replace the original sodium hydroxide-sodium acetate eluent. The main factors influencing the separation and detection performance of the proposed method, including the pulse amperage detection potential parameters and integration time, as well as the type and content of additives in the stabilizing solution, were optimized. The results showed that the proposed method had a good linear relationship between 10 and 3000 μg/L, with correlation coefficients (r2) of up to 0.999. The limits of detection (S/N=3) and quantification (S/N=10) were 1.53 and 5.10 μg/L, respectively. The relative standard deviations (RSDs) of the peak area and retention time of sulfides were less than 0.2% (n=6). The new method exhibited excellent stability, with up to 90% reduction in reagent costs. Compared with conventional ion chromatography-pulse amperometry, this method is more suitable for detecting low concentrations of sulfides in actual samples. Sulfides in a 250 mmol/L sodium hydroxide-0.8% (mass fraction) ethylenediaminetetraacetic acid disodium salt solution were effectively maintained for over 10 h. The new stabilizer significantly improved the reliability of both large-scale and long-term detection. The recovery of the proposed method was investigated by combining the system with a badge-type passive sampler. This sampling method requires no power devices; it is inexpensive, simple to operate, and can realize long-term sampling without the need for skilled personnel. Moreover, it can overcome the influence of short-term changes in pollutant concentration. The sampling results have high reference value for large-scale intervention-less pollutant monitoring in ultraclean rooms, museum counters, and other places. The results demonstrated that the recovery of the proposed method was greater than 95% for the blank sample and 80% for the sample plus standard solution. Finally, the newly established method was applied to determine H2S levels in air samples collected via passive sampling at school garbage stations. The measured results did not exceed the national limit.

Select

Determination of individual components in finished motor gasoline by dual-channel three-column gas chromatography LI Changxiu, WANG Yamin, ZHANG Yiwei, WANG Zheng 2024, 42 (8):  773-782.  DOI: 10.3724/SP.J.1123.2024.02013 Abstract ( 53 )   HTML ( 9 )   PDF (2061KB) ( 27 )   A method based on a dual-channel gas chromatograph equipped with three columns and three detectors was established for the determination of individual components in finished motor gasoline. The gasoline samples were separately introduced into the two injection ports of the chromatograph using two autosamplers. The components of the sample introduced into the first injection port (channel 1) were separated on a nonpolar PONA column (50 m×0.20 mm×0.5 μm) for gasoline analysis and detected by an flame ionization detector (FID). The components of the sample introduced into the second injection port (channel 2) were separated on another PONA column. Oxygenates (e.g., ethers and alcohols), other unconventional and prohibited additives that would co-elute with the hydrocarbons (e.g., methylal, dimethyl carbonate, sec-butyl acetate, and anilines), and some difficult-to-separate hydrocarbon pairs (e.g., 2,3,3-trimethylpentane and toluene) eluted from the PONA column and entered a DM-624 column (30 m×0.25 mm×1.4 μm) to achieve further separation according to the switch timetable using the Deans switch procedure and detected by an FID. The peak of 3-methylpentane, a common component in gasoline samples, also entered the DM-624 column by the Deans switch procedure for calculation purposes. The peak areas of target components on the PONA column in channel 1 were calculated using the peak areas on the DM-624 column as well as those of 3-methylpentane on both the DM-624 and PONA columns in channel 1 with a calibration factor between the two channels. The peak areas of co-eluted components were obtained by subtracting the calculated peak areas of the target components from those of the co-eluted peaks. The mass percentages of the individual components were calculated according to the normalization method using all peak areas on the PONA column in channel 1 with relative response factors. The mass percentages of the oxygenates, anilines, and individual hydrocarbons were determined, and the group-type distribution was calculated according to the carbon number. Separation and quantitation interferences between the additives and hydrocarbons were eliminated using this procedure. Twenty oxygenates and unconventional additives, each with a mass percentage of approximately 3%, were added to a real motor gasoline-92 sample and analyzed using the proposed method. The recoveries of the target components were between 90.1% and 118.2% with relative standard deviations (RSDs) between 0.2% and 5.1% (n=6). The analysis of a real ethanol-gasoline sample showed that the RSDs of contents of most components was less than 3% (n=6). Because the heart-cut of peaks using Deans switch technique requires the precise repeatability of retention times, the retention-time repeatability of components on the PONA column in channel 2 was investigated over an extended period of time after thousands of runs of real-sample analysis. The retention times of the same component in several randomly selected motor gasoline-92 samples varied from 0.01 to 0.03 min, indicating that the proper timetable for the Deans switch remained stable for two years. The precise repeatability of retention times was achieved owing to the high precision of the electric pneumatic control of the chromatograph and the stability of the column used. Real finished motor gasoline samples with different octane numbers (gasoline-92, gasoline-95, and ethanol gasoline-95) were analyzed using the developed method, and the results acquired were consistent with those of standard methods (GB/T 30519-2016, NB/SH/T 0663-2014, and SH/T 0693-2000). If some unconventional additives (such as methylal) were added to gasoline samples, the contents of these unconventional additives could also be detected, which means one run of the proposed method could provide results corresponding to three or four runs of different standard methods. The acquisition of information on the individual components of finished motor gasoline will assist in research on precise gasoline blending.

Technical Notes

Select

Simultaneous determination of 10 quaternary ammonium salt bactericides in oral care products by high performance liquid chromatography-evaporative light-scattering detection TANG Juan, DING Youchao, FEI Xiaoqing, WU Bin, QIAN Zhijuan, CHEN Shandan, LI Bai 2024, 42 (8):  783-791.  DOI: 10.3724/SP.J.1123.2023.10013 Abstract ( 47 )   HTML ( 11 )   PDF (1264KB) ( 48 )   Quaternary ammonium salt bactericides are broad-spectrum bactericides often used in oral care products because of their high antibacterial efficacy, strong penetration, and low toxicity. However, the excessive use of quaternary ammonium salt bactericides may cause contact dermatitis, scalding poisoning, and even death. Existing methods to determine quaternary ammonium salt bactericides are unable to meet current requirements owing to the lack of determination components. Therefore, establishing a simple and accurate method for the simultaneous detection of more quaternary ammonium salt bactericides is necessary. In this study, a method that couples sample pretreatment with high performance liquid chromatography-evaporative light-scattering detection (HPLC-ELSD) was developed for the simultaneous determination of quaternary ammonium salt bactericides in oral care products, including dodecyltrimethylammonium chloride, dodecyldimethylbenzylammonium chloride, benzethonium chloride, tetradecyl trimethyl ammonium chloride, tetradecyldimethylbenzylammonium chloride, N-hexadecyltrimethylammonium chloride, benzyldimethylhexadecylammonium chloride, trimethylstearylammonium chloride, stearyldimethylbenzylammonium chloride, and docosyltrimethylammonium chloride. Some of these bactericides do not absorb ultraviolet light, so a universal evaporative light-scattering detector was used owing to testing cost and stability concerns. The paste samples contained thickening agents, which are highly soluble in water but insoluble in organic solvents; these agents can seriously affect the results of sample pretreatment and damage the chromatographic column. Hence, sample dehydration was necessary. In this study, four dehydration methods were compared. Anhydrous sodium sulfate (Na2SO4) was selected, and the amount of Na2SO4 was optimized. Based on the solubility of the 10 target compounds and extraction efficiency, three extraction solvents were compared, and ethanol was selected. Ultrasonic extraction was the primary extraction process used in this study. The effects of different ultrasonication times, temperatures, and powers on the extraction recoveries were also investigated. Ultimately, the optimized conditions were as follows: extraction of the dehydrated paste and powder samples using ethanol at room temperature (25 ℃) for 20 min under 100 W ultrasound power, and dilution of the liquid sample with ethanol. After extraction, the samples were separated on an Acclaim Surfactant column (150 mm×4.6 mm, 5 μm) with 50 mmol/L ammonium acetate aqueous solution (pH=5.5) (A) and acetonitrile (B) as mobile phases. The gradient elution program were as follows: 0-5.0 min, 75%A-35%A, 5.0-15.0 min, 35%A-20%A, 15.0-20.0 min, 20%A, 20.0-21.0 min, 20%A-75%A, 21.0-25.0 min, 75%A. An external standard method was used for quantitative determination. The 10 compounds were analyzed within 25 min. Linear equations, correlation coefficients, and linear ranges were obtained by analyzing a series of mixed standard working solutions. The limits of detection (LODs, S/N=3) and quantification (LOQs, S/N=10) of the 10 components were determined. Stearyldimethylbenzylammonium chloride and docosyltrimethylammonium chloride showed good linear relationships in the range of 10-200 mg/L, while the other compounds demonstrated good linear relationships in the range of 5-100 mg/L. In all cases, correlation coefficients (R2) of no less than 0.9992 were obtained. The LODs and LOQs were in the range of 1.42-3.31 mg/L and 4.25-9.94 mg/L, respectively. Ten analytes were spiked in blank matrices, such as toothpaste (paste), mouthwash (liquid), and dentifrice powder (powder) at three levels, and the recoveries and precisions were calculated. The average recoveries were 87.9%-103.1%, and the corresponding relative standard deviations (RSDs) did not exceed 5.5% (n=6). The developed method was used to detect 109 oral care products. Benzyldimethylhexadecylammonium chloride and stearyldimethylbenzylammonium chloride revealed high detection rates. Moreover, the amount of stearyldimethylbenzylammonium chloride in one toothpaste sample exceeded regulatory requirements. Given its advantages of good precision and accuracy, the developed method is suitable for the quantitative analysis of the 10 aforementioned compounds in typical oral care products. The study findings can serve as a reference for the quality and safety monitoring of oral care products.

Select

Determination of sodium cyclamate in Baijiu by pre-column derivatization-high performance liquid chromatography with fluorometric detection GU Changyu, LI Xiaobin, CHAI Xiao, WANG Zhen, HOU Chenyu, KE Runhui 2024, 42 (8):  792-798.  DOI: 10.3724/SP.J.1123.2023.10016 Abstract ( 71 )   HTML ( 10 )   PDF (802KB) ( 65 )   Sodium cyclamate in Baijiu is a key item in the China National Food Safety Supervision and Inspection Plan. A simple, economical, sensitive, and reliable method is urgently needed for routine analysis and internal quality control. A method based on high performance liquid chromatography with fluorescence detection (HPLC-FLD) was developed for the determination of sodium cyclamate in Baijiu by o-phthalaldehyde derivatization. First, the sodium cyclamate in the sample solution was converted into amino compounds using the desulfurization reaction under acidic conditions. Next, 400 g/L sodium hydroxide solution was added to the sample solution for neutralization. The amino compounds in the sample solution were then derivatized with o-phthalaldehyde to produce indole-substituted derivatives that are capable of producing fluorescence signals. Separation was carried out on a C18 column (250 mm×4.6 mm, 5 μm) in isocratic elution mode using a mobile phase consisting of acetonitrile and phosphate buffer. Finally, the eluate was monitored using a fluorescence detector, and an external standard method was used for quantification. A good linear relationship was obtained in the range of 0.1-2.0 mg/L, with correlation coefficients greater than 0.999. The average recoveries of sodium cyclamate spiked at levels of 0.1-1.0 mg/kg in Baijiu samples ranged from 90.7% to 100.9%, with relative standard deviations (RSDs) of 3.5%-5.6% (n=6). The limits of detection and quantification were 0.03 and 0.10 mg/kg, respectively. Nine Baijiu samples collected from the market were tested, and the results demonstrated that the contents of sodium cyclamate detected by the developed method were consistent with those obtained using the liquid chromatography-tandem mass spectrometry (LC-MS/MS) method described in GB 5009.97-2016 (the third method). The proposed method is economical, sensitive, specific, and accurate; thus, it provides a basic approach for the determination of sodium cyclamate in Baijiu samples and has great potential for routine analysis in foodstuffs.

Select

Determination of electrosynthesized urea products by igh performance liquid chromatography based n porous graphitic carbon column SHEN Rui, LI Yongyi, GAO Xiaojing, SHI Chaoou 2024, 42 (8):  799-804.  DOI: 10.3724/SP.J.1123.2023.09013 Abstract ( 44 )   HTML ( 16 )   PDF (786KB) ( 21 )   Urea is a simple organic compound that is widely used in both the industry and daily life. Compared with conventional methods, the preparation of urea by electrochemical synthesis is more environmentally friendly and sustainable. However, after the reaction, low amounts of urea and high concentrations of inorganic ions, including \mathrm{N} {{\mathrm{O}}_3}^{-}, \mathrm{N} {{\mathrm{O}}_2}^{-}, \mathrm{N} {{\mathrm{H}}_4}^{+}, \mathrm{H} {{\mathrm{CO}}_3}^{-}, and \mathrm{C} {{\mathrm{O}}_3}^{2-}, with a comparatively high concentration of \mathrm{N} {{\mathrm{O}}_3}^{-}, remain in the solution. These ions tend to interfere with the urea measurements. Thus, detecting traces of urea in highly concentrated ionic matrices is challenging. Several urea detection methods, such as infrared spectrometry, the urease method, and high performance liquid chromatography (HPLC), are available. Among these methods, HPLC shows greater sensitivity and accuracy. However, urea is difficult to separate from \mathrm{N} {{\mathrm{O}}_3}^{-} on reversed-phase C18 columns. Porous graphitic carbon (PGC) columns have lower column loss and better baseline stability at low UV absorption wavelengths than ordinary reversed-phase C18 columns. In this study, a qualitative and quantitative analytical method based on a PGC column was established to detect urea from inorganic ions. The separation of urea from other ions was successfully achieved on a HypercarbTM PGC column (100 mm×4.6 mm, 5 μm). Experimental investigations were performed under the optimal chromatographic conditions, and gradient elution was performed with a H2O-25 mmol/L methanesulfonic acid aqueous solution as the mobile phase (initial mobile phase volume ratio, 98∶2). The column temperature was 30 ℃, the flow rate was 1.0 mL/min, and the injection volume was 25.0 μL. A diode array detector with a detection wavelength of 190 nm was selected because of the low UV absorption wavelengths of urea and impurity ions. The electrolyte product was passed through a 0.22 μm aqueous-phase filter membrane, and the resulting filtrate was analyzed under the optimized conditions. The results showed that urea was well separated from the other ions in the filtrate within 15 min. The urea measurements were unaffected by other ions present in the electrolyte. Moreover, none of the retention times of potentially interfering ions overlapped with those of urea. The background noise remained low and the baseline was smooth, even at a low detection wavelength of 190 nm. Methodological verification experiments showed that urea had a good linear relationship in the mass concentration range of 0.1-100 mg/L (r2≥0.9988). The limits of detection and quantification were 0.028 and 0.093 mg/L, respectively. When the electrolyte product was spiked with urea at three levels, the average recoveries were in the range of 112.0%-118.4%. Finally, an actual electrolyte sample was analyzed, and the results showed that urea could be detected quantitatively in this sample. The established method requires fewer pretreatment procedures because the samples only need to be filtered and analyzed. It also has a short analysis time and yields accurate, reliable, and specific results. Moreover, at an ultralow detection wavelength of 190 nm, the method demonstrated high sensitivity to urea and ensured a low background noise and baseline stability. Owing to the specific retention effect of the PGC column, the separation of urea at a high \mathrm{N} {{\mathrm{O}}_3}^{-} concentration was achieved without interference. Thus, the developed method can be applied for the detection of trace urea and other related ions in urea-containing electrolyte products.

Select

Application of ion chromatographic fingerprint analysis for quality evaluation of tobacco flavors XU Gaoyan, HE Xinying, ZHANG Lina, LIU Chongsheng, GAO Yang, HUANG Zhongping, LIU Huijun, WU Zhaoming, ZHANG Ruichao, SHI Hong 2024, 42 (8):  805-811.  DOI: 10.3724/SP.J.1123.2023.11008 Abstract ( 87 )   HTML ( 11 )   PDF (802KB) ( 44 )   Tobacco flavor, an important tobacco additive, is an essential raw material in cigarette production that can effectively improve the quality of tobacco products, add aroma and taste, and increase the suction flavor. The quality consistency of tobacco flavors affects the quality stability of branded cigarettes. Therefore, the quality control of tobacco flavors is a major concern for cigarette and flavor manufacturers. Physical and chemical indices, odor similarity, and sensory efficacy are employed to evaluate the quality of tobacco flavors, and the analysis of chemical components in tobacco flavors is usually conducted using gas chromatography (GC) and high performance liquid chromatography (HPLC). However, because the composition of tobacco flavors is complex, their quality cannot be fully reflected using a single component or combination of components. Therefore, establishing an objective analytical method for the quality control of tobacco flavors is of extreme importance. Chromatographic fingerprint analysis is routinely used for the discriminative analysis of tobacco flavors. Chromatographic fingerprints refer to the general characteristics of the concentration profiles of different chemical compounds. In the daily procurement process, fingerprints established by GC and HPLC are effective for the evaluation and identification of tobacco flavors. However, given continuous improvements in aroma-imitation technology, some flavors with high similarity cannot be directly distinguished using existing methods. In this study, a method for the determination of organic acids and inorganic anions in tobacco flavors based on ion chromatography (IC) was developed to ensure the quality consistency of tobacco flavors. A 1.0 g sample of tobacco flavors and 10 mL of deionized water were mixed and vibrated for 30 min. The aqueous sample solution was passed through a 0.45 μm membrane filter and RP pretreatment column in succession to eliminate interferences and then subjected to IC. Standard solutions containing nine organic acids and seven inorganic anions were used to identify the anions in the tobacco flavors, and satisfactory reproducibility was obtained. The relative standard deviations (RSDs) for retention times and peak areas were <0.71% and <6.02%, respectively. The chromatographic fingerprints of four types of tobacco flavors (samples A-D) from five different batches were obtained. Nine tobacco flavor samples from different manufacturers (samples AY1-AY3, BY1-BY2, CY1-CY2, DY1-DY2) were also analyzed to obtain their chromatographic fingerprints. Hierarchical cluster and similarity analyses were used to evaluate the quality of tobacco flavors from different manufacturers. Hierarchical clustering refers to the process of subdividing a group of samples into clusters that exhibit a high degree of intracluster similarity and intercluster dissimilarity. The dendrograms obtained using SPSS 12.0 indicated good quality consistency among the samples in different batches. Samples AY3, BY2, CY2, and DY1 clustered with the batches of standard tobacco flavors. Therefore, hierarchical cluster analysis can effectively distinguish the quality of products from different manufacturers. The Similarity Evaluation System for Chromatographic Fingerprint of Traditional Chinese Medicine (version 2.0) was used to evaluate the similarity between the standard tobacco flavors and products from different manufacturers. Among the samples analyzed, samples AY3, BY2, CY2, and DY1 showed the highest similarity values (>97.7%), which was consistent with the results of the hierarchical cluster analysis. This finding indicates that IC combined with chromatographic fingerprint analysis could accurately determine the quality of tobacco flavors. GC combined with ultrasonic-assisted liquid-liquid extraction was also used to analyze the tobacco flavors and verify the accuracy of the proposed method. Compared with GC coupled with ultrasonic-assisted liquid-liquid extraction, IC demonstrated more significant quality differences among certain tobacco flavors.

Teaching Research

Select

Experimental teaching reform of polymer molar mass determination using gel permeation chromatography coupled with light scattering QIAO Congde, YANG Wenke, LI Zhongwei, LIU Qinze, YAO Jinshui 2024, 42 (8):  812-818.  DOI: 10.3724/SP.J.1123.2023.12005 Abstract ( 48 )   HTML ( 11 )   PDF (1054KB) ( 20 )   Gel permeation chromatography coupled with light scattering (GPC-LS) is among the most common methods for determining the molar masses of polymers. GPC-LS is widely used in polymer science research and has been adopted for many industrial applications owing to its high sensitivity, accuracy, and precision. The determination of polymer molar masses using GPC-LS is an important experimental component of the “Polymer Physics Experiments” course. However, the present GPC-LS experimental teaching content tends to be overly simplistic and lacking in depth. Herein, the original experimental content is expanded and multiple sets of experiments are redesigned: (1) Using commercial polystyrene as an experimental sample, the molar mass, molar mass distribution, radius of gyration, and other molecular structure parameters are determined using GPC-LS; (2) Using two polyacrylonitriles with similar molecular structure parameters, subtle differences in the molar mass distributions of the samples are explored using differential mass distribution curves; (3) By comparing the chromatograms of a series of polyethylene glycols with different molar masses, the effect of molar mass on chromatographic peaks is investigated; and (4) For three different polymers (polyacrylonitrile, poly(methyl methacrylate), and poly(β-cyclodextrin)), the polymer chain conformations are analyzed using conformation plots (i.e., radius of gyration vs. molar mass). In addition, the experimental teaching method is modified to convert passive learning into active learning, thereby improving the students’ self-directed learning ability. This experimental teaching reform will help students obtain a more comprehensive understanding of GPC-LS principles and applications, stimulate their enthusiasm for learning, and improve the teaching quality of the experimental course.