List of Issues

Chinese Journal of Chromatography
2024, Vol. 42, No. 9
Online: 08 September 2024

Previous Issue    Next Issue



For Selected:

Download Citations EndNote Ris BibTeX

Toggle Thumbnails

Select

CONTENTS 2024, 42 (9):  0-0.  Abstract ( 33 )   PDF (3958KB) ( 46 )

Article

Select

Zirconium-based metal-organic framework composites for solid phase extraction of brevetoxin-A from seawater CHEN Zongbao, XIE Shiye, LIU Yongjun, ZHANG Wenmin, FANG Min, ZHANG Lan 2024, 42 (9):  819-826.  DOI: 10.3724/SP.J.1123.2024.02026 Abstract ( 109 )   HTML ( 19 )   PDF (2039KB) ( 55 )   Red tides are a type of natural marine disaster caused by harmful algae characterized by a high toxicity, wide distribution, and long duration. Since the concentration of algal toxins in seawater increases with the occurrence of red tides, algal toxins detected in seawater could be used to predict the occurrence and evolution of red tides. Brevetoxin-A (BTX-A) is a secondary metabolite produced by the harmful algae Karenia brevis, whose detection in seawater could form the basis of an accurate warning system for incoming red tides. However, due to the inherent complexity of the seawater matrix and the extremely low levels of BTX-A in seawater, the use of instruments for its direct detection is difficult. Therefore, there is an urgent need to develop a sample pretreatment method for the efficient enrichment of BTX-A in seawater. In this study, a metal-organic backbone material (UiO-66) and its composite with silica microspheres (SiO2@UiO-66) were successfully synthesized using the solvothermal method. The prepared SiO2@UiO-66 exhibited good hydrophilicity, water stability, and large specific surface area. Furthermore, it also exhibited hydrogen bonding and electrostatic interactions with BTX-A, had a strong affinity for BTX-A, and was able to efficiently adsorb BTX-A in complex matrices. Therefore, SiO2@UiO-66 showed potential as a novel packing material for the extraction of BTX-A from solid phase extraction columns. Combined with high performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS), a highly sensitive detection method for the determination of BTX-A in marine water was established. The established analytical method had a low detection limit (3.0 pg/mL), a wide linear range (10.0 -200.0 pg/mL), and a good linear relationship (R=0.9992). Combined with the Fujian Province Red Tide Monitoring and Early Warning Information 2021 issued by the Fujian Provincial Oceanic and Fisheries Bureau, the analytical method established herein was successfully applied to analyze and monitor the content of BTX-A in actual seawater samples. This highlights the proposed system’s potential for use as an early warning factor in the monitoring of red tides, representing a simple and fast pretreatment methodology for the detection of BTX-A in seawater.

Select

Determination of ten bisphenols and five parabens in urine by solid supported liquid-liquid extraction and liquid chromatography-tandem mass spectrometry XUE Yufan, SHANG Ting, CUI Juntao, ZHAO Lingjuan, LI Pei, ZENG Xiangying, YU Zhiqiang 2024, 42 (9):  827-836.  DOI: 10.3724/SP.J.1123.2024.01001 Abstract ( 138 )   HTML ( 29 )   PDF (1763KB) ( 79 )   Bisphenols (BPs) and parabens (PBs) are of great concern for environmental pollution and human health because of their endocrine-disrupting effects and potential health hazards. Urinary biomonitoring of BPs and PBs can provide basic data for human internal exposure evaluation, which is a prerequisite for accurately assessing their health risks. In this study, we developed a new pretreatment procedure based on solid supported liquid-liquid extraction (SLE) for the simultaneous separation of ten BPs and five PBs in human urine, followed by high performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) analysis. In the instrumental analysis, the HPLC conditions and MS/MS parameters were comprehensively optimized. Accurate qualitative and quantitative determination of ten BPs and five PBs was achieved by introducing a ternary gradient elution system of water, methanol, and acetonitrile for LC separation. During sample pretreatment, the extraction solvent and elution volume were optimized. Specifically, urine samples were held at room temperature and centrifuged at 3000 r/min for 10 min. The supernatant (2 mL) was then transferred to a glass tube, and the pH was adjusted to 5.0 using HCl (0.5 mL; 0.1 mol/L) and NaAc-HAc buffer (1.5 mL). Thereafter, β-glucuronidase-arylsulfatase (20 μL) and surrogate standard solutions (10 ng;13C12-BPS,13C12-BPAF,13C6-MeP, and 13C6-BuP) were added, and the mixture was incubated in a shaker bath in the dark at 37 ℃ for 16 h. After incubation, the hydrolyzed sample (4 mL) was loaded onto an SLE cartridge and equilibrated for a minimum of 5 min to ensure the solution was completely absorbed by the packing material. Subsequently, the target chemicals were eluted with a mixed ethyl acetate/n-hexane solution (3∶7, v/v; 15 mL). Separation of the targets was performed on a ZORBAX SB-C18 reversed-phase column (250 mm×4.6 mm, 5 μm) using an acetonitrile-methanol-water system as the mobile phase. The method was verified by spiking mixed urine samples at three levels (1, 5, and 50 μg/L), with the recoveries ranging from 84.3% to 119.8%. Except for bisphenols (BPS), whose matrix effect was calculated as -21.8%, the matrix effects of other analytes were lower than 20%, indicating low matrix interference. The linear ranges of the analytes varied from 0.1-500 μg/L to 1-500 μg/L, with correlation coefficients higher than 0.995. The method limits of quantification for target chemicals ranged from 0.03 to 0.30 μg/L, and the relative standard deviations of intra- and inter-day experiments were 1.4%-8.4% and 5.7%-14.6%, respectively, suggesting high stability and reproducibility. The method was successfully applied to the determination of ten BPs and five PBs in 10 urine samples from a general population. The concentrations of target chemicals in the human urine samples varied. Methylparaben (MeP), ethylparaben (EtP), propylparaben (PrP), and bisphenol A (BPA) were detected in all samples, with median mass concentrations of 1.10, 0.60, 0.21, and 0.55 μg/L, respectively. The detection rates of the other chemicals were less than 50%, which may be related to the production and use of specific chemicals, their bioavailability, and biological metabolism in humans.

Select

Identification of chemical components of large-leaf yellow tea by ultra performance liquid chromatography-quadrupole time-of-flight mass spectrometry HUANG Ruotong, RONG Xuewen, FU Xiaojie, CHEN Chang, CHU Jun, XU Na, WU Huan 2024, 42 (9):  837-855.  DOI: 10.3724/SP.J.1123.2023.10021 Abstract ( 79 )   HTML ( 21 )   PDF (4811KB) ( 45 )   Large-leaf yellow tea, a slightly fermented yellow tea that is unique to China, has a stronger hypoglycemic effect than other tea varieties, such as green and black tea. Research on large-leaf yellow tea has focused on its hypoglycemic effect owing to the lack of comprehensive techniques to characterize its chemical components; thus, its development and further promotion are limited. Therefore, the development of a reliable analytical method to fully characterize the chemical components of large-leaf yellow tea is urgently required. In this study, a reliable strategy based on the data-acquisition technology of ultra performance liquid chromatography-quadrupole time-of-flight mass spectrometry (UPLC-Q TOF/MS) was established to rapidly screen and analyze the main chemical components of large-leaf yellow tea by combining the information of neutral loss groups and characteristic fragment ions. The chromatographic separation experiments were performed on a Waters ACQUITY UPLC BEH C18 column (100 mm×2.1 mm, 1.7 μm) with gradient elution using 0.1% formic acid aqueous solution and acetonitrile as the mobile phases. The flow rate was 0.2 mL/min, the sample volume was 2 μL, and the column temperature was 35 ℃. The mass spectral information of the components in a large-leaf yellow tea solution was collected using the full-information tandem MS (MSE) technique in positive and negative ion modes. The specific chemical components of large-leaf yellow tea was identified as follows. First, a self-established database of tea chemical components was constructed based on the literature. The mass spectral cleavage pathways of different types of compounds in large-leaf yellow tea were then sorted using reference substances, and the characteristics of the fragment ions and neutral loss groups were summarized. The precise mass-to-charge ratio of the target chemical components were then obtained based on the mass spectral information. Finally, the structures of the compounds in large-leaf yellow tea were confirmed based on their chromatographic retention times, mass spectral cleavage pathways, characteristic fragment ions, and neutral loss groups. A total of 87 chemical components, including 10 catechins, 32 flavonoids, 16 phenolic acids, 12 tannins, 6 theaflavins, and 11 compounds in other classes, were identified in large-leaf yellow tea. Representative compounds of various classes, including gallocatechin gallate, quercetin, vitexin, gallic acid, chlorogenic acid, 1,3,6-tri-O-galloyl-β-D-glucose, and theaflavin, were selected, and their characteristic fragment ions and neutral loss groups were investigated in detail to reveal the cleavage pathways of different types of compounds in large-leaf yellow tea. The UPLC-Q TOF/MS method established in this study can comprehensively identify the main chemical components of large-leaf yellow tea in a simple, highly sensitive, stable, and reliable manner. This study provides a scientific basis and data support for the discovery of functional ingredients and quality evaluation of large-leaf yellow tea.

Select

Determination of eight neonicotinoid pesticides in wastewater by solid phase extraction combined with liquid chromatography-tandem mass spectrometry WANG Haitang, LI Hanyin, LU Qiwei, HE Shilong 2024, 42 (9):  856-865.  DOI: 10.3724/SP.J.1123.2023.11010 Abstract ( 132 )   HTML ( 23 )   PDF (2496KB) ( 78 )   Neonicotinoid pesticides are a relatively new class of pesticides that have garnered significant attention owing to their potential ecological risks to nontarget organisms. A method combining solid phase extraction with liquid chromatography-tandem mass spectrometry (SPE-LC-MS/MS) was developed for the rapid and accurate detection of eight neonicotinoid pesticides (dinotefuran, E-nitenpyram, thiamethoxam, clothianidin, imidacloprid, imidaclothiz, acetamiprid, and thiacloprid) in wastewater. The chromatographic mobile phase and MS parameters were selected, and a single-factor method was used to determine the optimal column type, extraction volume, sample loading speed, and pH for SPE. The optimal parameters were as follows: column type, HLB column (500 mg/6 mL); sample extraction volume, 500 mL; sample loading speed, 10 mL/min; and sample pH, 6-8. The matrix effects of the wastewater samples were reduced by optimizing the chromatographic gradient-elution program, examining the dilution factor of the samples, and using the isotope internal standard calibration method. Prior to analysis, the wastewater samples were diluted 5-fold with ultrapure water for pretreatment. Subsequently, 2 mmol/L ammonium acetate aqueous solution containing 0.1% (v/v) formic acid and methanol was used as mobile phases for gradient elution on a ZORBAX Eclipse Plus C18 column (100 mm×2.1 mm, 1.8 μm). The samples were quantified using positive-ion multiple reaction monitoring (MRM) mode for 10 min. Imidacloprid-d4 was used as the isotope internal standard. The SPE process was further optimized by applying response surface methodology to select the type and mass of rinsing and elution solvents. The optimal pretreatment of the SPE column included rinsing with 10% methanol aqueous solution and elution with methanol-acetonitrile (1∶1, v/v) mixture (7 mL). The eight neonicotinoid pesticides showed satisfactory linearity within the relevant range, with linear correlation coefficients (r) all greater than 0.9990. The method detection limits (MDLs) ranged from 0.2 to 1.2 ng/L, and the method quantification limits (MQLs) ranged from 0.8 to 4.8 ng/L. The average recoveries of the eight neonicotinoid pesticides were in the range of 82.6%-94.2% at three spiked levels, with relative standard deviations (RSDs) ranging from 3.9% to 9.4%. Finally, the optimized method was successfully applied to analyze wastewater samples collected from four sewage treatment plants. The results indicated that the eight neonicotinoid pesticides could be generally detected at concentrations ranging from not detected (ND) to 256 ng/L. The developed method has a low MDL and high accuracy, rendering it a suitable choice for the trace detection of the eight neonicotinoid pesticides in wastewater when compared with other similar methods. The proposed method can be utilized to monitor the environmental impact and assess the potential risks of neonicotinoid pesticides in wastewater, thus promoting the protection of nontarget organisms and the sustainable use of these pesticides in agriculture.

Select

Simultaneous determination of 61 hormones in water by solid phase extraction-ultra performance liquid chromatography-tandem mass spectrometry CHEN Yueqin, MA Ming, XU Hongdan, PAN Chunyan 2024, 42 (9):  866-874.  DOI: 10.3724/SP.J.1123.2023.11014 Abstract ( 120 )   HTML ( 31 )   PDF (1105KB) ( 64 )   Concerns over the emergence of steroid hormones as pollutants in water have grown. Steroid hormone compounds present challenges in the simultaneous detection of total residual hormones owing to their analogous structures and diverse types. In this study, we established a rapid and high-throughput continuous online method based on solid phase extraction (SPE) coupled with ultra performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) for the simultaneous determination of 61 hormone components, including 48 glucocorticoids, 1 mineralocorticoid, 4 androgens, and 8 progesterones, in water. Various SPE columns were investigated to assess their extraction efficiency for enriching and purifying target compounds in a large sample volume (1 L). An HC-C18 SPE column was selected because of its superior performance. Acetonitrile was used as a washing solution during SPE to ensure that the majority of the tested substances achieved recoveries exceeding 70% and effectively avoid interferences from water-soluble components. Various C8 and C18 columns were tested, and the optimal HPLC conditions for hormone retention were established. We systematically evaluated different UPLC columns and mobile phases, including methanol-water and acetonitrile-water systems with 0.1% formic acid added to the aqueous phase. The optimized UPLC conditions were as follows: BEH C18 column (100 mm×2.1 mm, 1.7 μm); column temperature, 40 ℃; flow rate, 0.3 mL/min; injection volume, 5 μL; mobile phase A: 0.1% formic acid aqueous phase; mobile phase B: acetonitrile. Gradient elution was performed as follows: 0-0.5 min, 30%B; 0.5-15.0 min, 30%B-75%B; 15.0-18.0 min, 75%B-98%B; 18.0-19.0 min, 98%B; 19.0-19.1 min, 98%B-30%B; 19.1-20.0 min, 30%B. Both positive- and negative-ion modes were explored in the UPLC-MS/MS experiment to obtain the full scan of the parent ions, and positive mode was finally selected for electrospray ionization (ESI). Two product ions exhibiting strong signals and minimal interference were selected for quantitative and qualitative ion analyses, using an external standard method for quantification. MS/MS was performed in positive-ion (ESI+) mode with multiple reaction monitoring (MRM) scanning. The MS/MS parameters were as follows: atomizing gas pressure, 379 kPa; curtain air pressure, 241 kPa; spray voltage, 5500 V; desolvation temperature, 550 ℃; collision exit voltage (CXP), 13 V; intake voltage (EP), 10 V; and residence time of each ion pair, 0.5 ms. Other instrument settings, such as the collision energy and declustering voltage, were also optimized. The 61 hormones exhibited excellent linear relationships within their corresponding concentration ranges, with correlation coefficients greater than 0.99. The method detection limits (MDLs) were in the range of 0.05-1.50 ng/L. The average recoveries of the 61 hormones across three spiked levels ranged from 62.3% to 125.2%, with relative standard deviations (RSDs, n=6) of 1.1%-10.5%. Using this method, we successfully detected 10 hormone components (cortisone, fluticasone propionate, ciclesonide, betamethasone dipropionate, clobetasone butyrate, diflucortolone valerate, halobetasol propionate, isoflupredone, difluprednate, and hydroxyprogesterone caproate) in various surface water and groundwater samples collected from the Taihu Basin region. The SPE-UPLC-MS/MS method presented in this paper is simple, highly sensitivity, and exceptionally accurate. Thus, it exhibits promising potential for tracing targeted hormone residues in water and will be of great value in monitoring and ensuring water safety. Finally, a regional analysis was conducted on the hormone levels in water, and suggestions were made for the targeted treatment of hormone residues in future sewage treatment processes.

Select

Rapid determination of chlorate and perchlorate in tea by ion exchange chromatography-tandem mass spectrometry YE Mingli, ZHAO Guohua, WANG Yong, LIN Jirun, LIU Wenxin, LU Jie, ZHAO Yonggang, CAO Ban 2024, 42 (9):  875-880.  DOI: 10.3724/SP.J.1123.2023.10026 Abstract ( 80 )   HTML ( 14 )   PDF (831KB) ( 59 )   Ion exchange chromatography-tandem mass spectrometry (IEC-MS/MS) has recently become the preferred method for detecting ionic substances in tea. In this study, an IEC-MS/MS method was developed for the rapid determination of chlorate and perchlorate residues in tea samples. The optimal sample extraction process, pretreatment column, and chromatographic and mass spectrometric conditions were systematically investigated. In the optimal process, the tea samples were ultrasonically extracted with methanol-water (13∶7, v/v), and a PRiME HLB SPE column was used to purify the sample extract. An AceChrom Hybri-A IEC column (150 mm×2.1 mm, 5.0 μm) was used for separation, and 100 mmol/L ammonium acetate-acetonitrile (40∶60, v/v) was used as the mobile phase for isocratic elution. The flow rate was 0.3 mL/min, the column temperature was 40 ℃, and the injection volume was 5.0 μL. The mass spectrometric data were collected in negative electrospray ionization mode combined with multiple reaction monitoring (MRM) mode to achieve the rapid and accurate separation and qualitative analysis of the desired chemical components. Quantification was performed using the internal standard (IS) method. The measurement results showed a good linear relationship when the mass concentrations of chlorate and perchlorate were between 2.00-200 and 1.00-100 μg/L, respectively, with correlation coefficients (r2) greater than 0.9990. The average recoveries of chlorate and perchlorate at three spiked levels of low, medium, and high ranged from 88.54% to 97.25% with relative standard deviations (RSDs, n=7) of 3.2%-5.2%. The limits of detection for chlorate and perchlorate were 12.0 and 8.0 μg/kg, respectively, while the limits of quantification were 40.0 and 26.6 μg/kg, respectively. The results of tests conducted to assess the linearity, specificity, accuracy, precision, and applicability of the method to the analysis of chlorate and perchlorate in 15 tea samples collected from a local market demonstrated its validity for the routine analysis of tea samples. The proposed method is simple, rapid, sensitive, and accurate, and can meet requirements for the rapid screening and quantitative analysis of residual trace chlorate and perchlorate in large quantities of tea samples.

Select

Analysis of phthalate esters from vegetable oils by gas chromatography-mass spectrometry coupled with headspace solid-phase microextraction using cyclodextrin-based hypercrosslinked polymer coated fiber ZHANG Pengcheng, WANG Yuan, LIU Kunling, SUN Yaming, HE Lijun, ZHAO Wenjie 2024, 42 (9):  881-890.  DOI: 10.3724/SP.J.1123.2024.01019 Abstract ( 64 )   HTML ( 29 )   PDF (2359KB) ( 33 )   Phthalate esters (PAEs) are used as additives to enhance the pliability and malleability of plastics. These substances frequently migrate from packaging materials to vegetable oils because of the absence of covalent bonds. Over time, this migration could result in the accumulation of PAEs in the human body through ingestion, contributing to various diseases. Therefore, accurate qualitative and quantitative analyses of PAEs in vegetable oils are imperative to assess the origins of contamination and investigate their toxicity, degradation, migration, and transformation patterns. However, the concentration of PAEs in most samples is low, and the composition of vegetable oils is complex. Thus, PAEs must be enriched and purified using appropriate sample pretreatment procedures before analysis. Common methods for pretreating PAEs in oil include solid-phase extraction (SPE), dispersive SPE, and magnetic SPE. These techniques require time-consuming and labor-intensive procedures such as oil dissolution, solvent extraction, and degreasing. These approaches also require numerous solvents and containers, increasing the risk of sample cross-contamination. Solid-phase microextraction (SPME) integrates sampling, extraction, purification, concentration, and injection into a single process, significantly accelerating analytical testing and reducing the potential for sample cross-contamination. In headspace (HS) mode, the analytes achieve equilibrium on the coating and are extracted in the gas phase. The fibers are shielded from nonvolatile and high-relative molecular mass substances in the sample matrix. Thus, SPME is an ideal method for extracting volatile compounds in vegetable oils. When HS-SPME coupled with gas chromatography-mass spectrometry (GC-MS), it can achieve the rapid screening of PAEs in vegetable oil. In this study, an SPME with cyclodextrin-based hypercrosslinked polymers (BnCD-HCP) coated on stainless steel fibers was employed to extract PAEs from vegetable oil. The structure and morphology of the polymers were characterized using Fourier-transform infrared spectroscopy, nuclear magnetic spectroscopy, and scanning electron microscopy. BnCD-HCP exhibited high stability and diverse interactions, including π-π, hydrophobic, and host-guest interactions. The oil samples were incubated with methanol, and the PAEs were extracted from the headspace using the probe. The optimal extraction parameters included an extraction time of 20 min, extraction temperature of 50 ℃, desorption time of 4 min, and desorption temperature of 275 ℃. The BnCD-HCP/HS-SPME method was evaluated under optimized experimental conditions. The limits of detection (LODs) and quantification (LOQs) were determined by applying signal-to-noise ratios (S/N) of 3 and 10, respectively. Method accuracy was evaluated using relative standard deviations (RSDs). Single-needle precision was evaluated by conducting three consecutive analyses at 3 h intervals within a day. Inter-needle precision was assessed by conducting the same analyses (three replicates) with differently coated fibers. The 12 PAE compounds exhibited good linearity with correlation coefficients (R2) of at least 0.99. The LODs and LOQs ranged from 0.21 to 3.74 μg/kg and from 0.69 to 12.34 μg/kg, respectively. The RSDs were in the range of 1.8%-11.4% and 5.1%-13.9% for the single-needle and needle-to-needle methods, respectively. The proposed method was applied to soybean, peanut, and sunflower oils, and two PAEs were found in all three oils. Moreover, the method demonstrated good precision (RSD=1.17%-11.73%) and recoveries (72.49%-124.43%). Compared with other methods, the developed method was able to extract many target analytes and had a low or comparable LOD and high recovery. More importantly, this method does not require tedious operations such as solvent extraction and purification. Consequently, the developed method can be used to extract not only PAEs in oils but also other substances with a high lipid content.

Select

Chiral porous organic cage used as stationary phase for gas chromatographic separation of chiral and achiral compounds HUANG Bin, CHEN Juan, WANG Bangjin, ZHANG Junhui, XIE Shengming, YUAN Liming 2024, 42 (9):  891-902.  DOI: 10.3724/SP.J.1123.2024.01025 Abstract ( 80 )   HTML ( 23 )   PDF (3667KB) ( 38 )   Porous organic cages (POCs) are a new type of molecular material. The well-defined cavities, abundant host-guest recognition ability, and good solubility of POCs render them attractive for use in various fields such as molecular recognition, gas adsorption, molecular containers, sensing, catalysis, chromatographic separation. In this study, a chiral POC (CPOC) was synthesized via the Schiff base condensation of 4,4',4″,4″'-(ethene-1,1,2,2-tetrayl)tetrabenzaldehyde with (R,R)-1,2-cyclohexanediamine. CPOC was characterized using nuclear magnetic resonance (NMR) spectroscopy, Fourier transform-infrared (FT-IR) spectroscopy, mass spectroscopy (MS), and thermogravimetric analysis (TGA). The FT-IR spectrum of CPOC showed a strong peak at 1638 cm-1, which was attributed to imine (-C=N-) absorption, as well as absorption peaks at 2928 and 2856 cm-1, which were attributed to the stretching vibrations of -CH2- and -CH-, respectively. MS analysis of CPOC revealed peaks at m/z=1801.9797, m/z=901.9914, and m/z=601.6631, corresponding to [M+H]+, [M+2H]2+, and [M+3H]3+, respectively, and indicating a molecular formula of CPOC (C126H120N12). The TGA curve of CPOC indicated high thermal stability up to 360 ℃; thus, the material is suitable for use as a stationary phase for gas chromatography (GC). CPOC was coated on the inner wall of a capillary column using the static coating method to prepare a GC column. Scanning electron microscopy (SEM) was used to characterize the coating condition of the fabricated column. The SEM images showed that the column had a uniform coating with a thickness of approximately 200 nm. Column efficiency was determined to be 3500 plates/m using n-dodecane as a target at 120 ℃. The polarity of the CPOC stationary phase was evaluated using McReynolds constants, which were measured using benzene, 1-nitropropane, 2-pentanone, pyridine, and 1-butanol as probe molecules at 120 ℃. The average McReynolds constant was 152, indicating that CPOC is a moderately polar stationary phase. The ability of the column to separate organic mixtures, isomers, and chiral compounds was subsequently investigated. All components of the four organic mixtures (n-alkanes, aromatics, n-alcohols, and Grob mixtures) tested achieved baseline separation on the column. In addition, nine positional isomers of disubstituted benzenes were well separated, and seven (o,m,p-nitrotoluene, o,m,p-nitrochlorobenzene, o,m,p-nitrobromobenzene, o,m,p-bromotoluene, o,m,p-dichlorobenzene, o,m,p-chloroaniline, and o,m,p-bromoaniline) achieved baseline separation. Some polar and apolar structural isomers, such as pentanol, dimethylphenol, dimethylaniline, butanol, and C9 aromatic hydrocarbon isomers, were also well separated on the column. Five cis/trans-isomers (nerol/geraniol, cis/trans-1,3-dichloropropene, cis/trans-1,2,3-trichloropropene, cis/trans-citral, and cis/trans-decahydronaphthalene) were baseline-separated on the column. More importantly, the column successfully separated 12 chiral compounds, indicating good chiral separation ability. Among these chiral compounds, five (ethyl 3-hydroxybutyrate, a valine derivative, a glutamic acid derivative, 1,2-butanediol diacetate, and 1,2-epoxybutane) achieved baseline separation. Six of these chiral compounds (ethyl 3-hydroxybutyrate, the valine derivative, the glutamic acid derivative, 1,2-epoxybutane, epichlorohydrin, and epibromohydrin) could not be separated on a β-DEX 120 column but were well separated on the developed column. Moreover, the separation efficiency of 1,2-butanediol diacetate and the isoleucine derivative on this column was better than that on the β-DEX 120 column. Separation of the glutamic acid derivative and o,m,p-nitrotoluene was performed before and after the column was used for repeated injections to explore its repeatability. The retention times and selectivity observed after 80, 160, and 500 injections were nearly unchanged compared with those obtained following the first use of the column, indicating that the column has good repeatability. The column was conditioned at 280 ℃ for a certain period to examine its thermal stability. Separation of 3-hydroxybutyrate and o,m,p-nitrochlorobenzene after the column was conditioned at 280 ℃ for 2, 4, or 8 h revealed no obvious changes compared with the first use of the column, indicating that the column had good thermal stability. Thus, CPOC is a stationary phase with good application potential for GC.

Select

On-line enrichment and separation of glycoprotein by capillary electrophoresis based on pH response coating column ZHANG Jian, XU Caifeng, MA Cailian, HE Maofang, ZHANG Bo, LIU Chunye 2024, 42 (9):  903-908.  DOI: 10.3724/SP.J.1123.2023.09021 Abstract ( 33 )   HTML ( 21 )   PDF (1168KB) ( 16 )   A capillary column coated with 3-aminophenylboronic acid (APBA)-functionalized gold nanoparticles (AuNPs@APBA) was prepared via electrostatic self-assembly. The coated column exhibited anti-nonspecific adsorption of glycoproteins, enabling selective online enrichment during capillary electrophoresis (CE). First, gold nanoparticles (AuNPs) were synthesized using the sodium citrate reduction method. Then, APBA was self-assembled electrostatically on the surface of the AuNPs to obtain AuNPs@APBA. This nanomaterial was bonded to the inner wall of a capillary through ion adsorption to produce a AuNPs@APBA-coated capillary column. Glycoproteins were adsorbed via bond formation with boric acid groups under alkaline conditions (pH 8) to generate borate esters. Under acidic conditions (pH 3), the borate esters dissociated to release the glycoproteins, thereby achieving the selective online enrichment and separation of glycoproteins. The AuNPs and AuNPs@APBA were characterized using Fourier transform infrared spectroscopy, and their sizes and Zeta potentials were determined. In addition, the electroosmotic flow (EOF) of the AuNPs@APBA-coated capillary column was measured. The results showed that the surface of the AuNPs was successfully modified with APBA and that AuNPs@APBA was adsorbed on the inner wall of the capillary. The peak area of ovalbumin (OVA) on the AuNPs@APBA-coated column was 26.46 times higher than that on a bare column via conventional electrophoresis. In contrast, the peak area of bovine serum albumin (BSA) only increased by 8.47 times, indicating that the AuNPs@APBA coated column selectively enriched glycoproteins. Evaluation of the reproducibility and stability of this method revealed that the AuNPs@APBA coated capillary column could be used continually for 33-67 h. The relative standard deviations (RSDs) of the peak areas for intra-day (n=5) and inter-day (n=6) analyses were 2.2% and 3.0%, respectively. The developed method was successfully applied to enrich glycoproteins in a 1×106-fold diluted egg white sample. Glycoproteins were not detected using conventional electrophoresis on the bare column, whereas the AuNPs@APBA-coated capillary column effectively enriched and separated glycoproteins, resulting in a peak area of 10469 mAU·ms. Furthermore, the entire enrichment and separation process was completed within 3 min. This new online enrichment and separation method for glycoproteins has the advantages of low sample consumption, simple operation, and high separation efficiency.

Technical Notes

Select

A headspace injection double-column dual-detector gas chromatography system for the analysis of 12 volatile compounds such as ethanol in human blood ZHENG Qiongying, ZHI Yujie, DUAN Wenjia, LÜ Min, XIAO Yue, XIANG Ping, CHEN Hang, YUN Keming 2024, 42 (9):  909-917.  DOI: 10.3724/SP.J.1123.2023.12015 Abstract ( 78 )   HTML ( 26 )   PDF (871KB) ( 33 )   Based on the technical methods of GB/T 42430-2023 and GA/T 204-2019, this study established an analytical method for headspace injection double-column dual-detector (hydrogen flame ion detector) gas chromatography for the simultaneous analysis of at least 12 volatile compounds, including ethanol, in human blood using two different equipment platforms and chromatographic columns. A 100 μL blood or urine sample and a 0.04 g/L tert-butanol working solution prepared as an internal standard are introduced into the headspace sample bottle and then sealed, mixed, and placed on the headspace sampler rack. Using different equipment platforms and columns, methodological parameters such as the limit of detection (LOD), limit of quantification (LOQ), precision, and accuracy of the method were systematically evaluated. The chromatographic separation of acetone, alcohols and benzenes using the established method was satisfactory. The linear ranges, linear correlation coefficients (r), and LODs of acetone and six alcohols, including ethanol, were 0.10-3.00 g/L, >0.997, and 0.05 g/L, respectively. The LOQs were 0.10 g/L for all other compounds, excluding n-propanol (0.005 g/L). Additionally, the linear ranges, r values, LODs, and LOQs of benzene and four benzene derivatives were 0.05-50 mg/L, >0.995, 0.02 mg/L, and 0.05 mg/L, respectively (Column J&W DB-BAC1 UI and Column Rtx-BAC-PLUS 2). The average recoveries of compounds on J&W DB-BAC1 UI and Rtx-BAC-PLUS 2 columns ranged from 92.2% to 111.6%, and the relative standard deviations (RSDs, n=6) ranged from 0.4% to 7.4%. The LOD, LOQ, precision, accuracy, and linearity of the established method met the requirements of relevant standards, and no significant differences arose between the methodological parameters of the two platforms. CNAS-GL006 (2019) and JJF 1059.1-2012 were used as guides to evaluate the uncertainty of ethanol on two different sets of equipment platforms and chromatographic columns. The ethanol uncertainty was mainly derived from the calibration curve; however, the confidence probability was 95% (k=2). According to the analysis of the verification samples and real samples, the established method is suitable for the high-precision quantitative analysis of acetone and six alcohols and five benzene derivatives in human blood and other body fluids. It can be used in practical scenarios such as judicial identification and the detection of poisons.

Teaching Research

Select

Exploration and practice of ideological and political education in instrumental analysis courses: a case study on chromatography course teaching ZHANG Yida, ZHANG Haixia 2024, 42 (9):  918-921.  DOI: 10.3724/SP.J.1123.2024.04005 Abstract ( 84 )   HTML ( 27 )   PDF (746KB) ( 47 )   Instrumental analysis is an important professional course for many chemistry majors. Its teaching content is rich, diverse and is closely related to daily life. Moreover, this course contains a large number of ideological and political resources. This study investigates chromatography technology in instrumental analysis as an example, focusing on aspects such as chromatography knowledge, solution preparation, standard operations, and guided experiments, to deeply explore the elements of ideological and political education and organically integrate them into the teaching of instrumental analysis courses. Academic teaching of professional knowledge increases the diversity and richness of the teaching content and enhances the innovative skills of the students. In addition, this teaching method can inspire students to establish life goals and great ideals, with the aim of ultimately cultivating moral people.